Loading.

. Location setup: select your country and time zone
    • Format: +/-hh:mm
    . Off peak charging
    According to local regulations, by default, the EVCS must be configured to NOT charge between 8 AM - 11 AM, and 4 PM - 10 PM on weekdays (OFF-peak charging). You can deactivate it now or at any time after the 'First setup' procedure.
    . WiFi setup: configure your WiFi network
    №SSIDPasswordUseDelete
    . Access setup: assign your username and password
          . Charging current setup: set the maximum charging current
          . Saving settings
          A
          Grid

          L1:
          L2:
          L3:
          Inverter / Charger

          Absorption

          AC loads

          L1:
          L2:
          L3:
          Solar yield

          Battery

          EVCS

          Manual
          0:0
          Session cost
          Session saved cost
          Total energy
          --
          Updated: --
          SoC -- % → -- %
          Range -- km
          Session cost
          Session saved cost
          Total energy
          0.0 W
          Connected
          Session time
          Session energy
          Session cost
          --
          Updated: --
          SoC -- % → -- %
          Range -- km
          Session time
          Session energy
          Session cost
          Session saved cost
          Total energy
          Backup & Reset
          Updating firmware. Do not turn off the power...
          0%
          Firmware successfully updated. Wait for the system reboot...
          Firmware update in progress. Please wait...
          Updating firmware. Do not turn off the power...
          0%
          The FW update procedure is in progress now. Please wait...
          Firmware successfully updated. Wait for the system reboot...
          Access
                Bluetooth
                Charger
                • Renault Zoe - 10A
                • Coefficients equal to 1.0 leave the actual power value unchanged
                • Coefficients greater than 1.0 increase the actual power value
                • Coefficients less than 1.0 decrease the actual power value
                Date & Time
                  • Format: +/-hh:mm
                  A power-down will result in loss of date and time information.
                  Display
                  Ethernet
                  GX device
                  • Communication with the GX device via Modbus TCP
                  • Verify that the 'GX Modbus TCP server' is enabled in 'GX Settings/Integrations'
                  • Use the 'Discover' button to search for GX devices on your network, or enter the 'IP' and 'VRM ID' manually
                  • Use the 'Check' button to test communication with the selected GX device
                  • Set 'Communication' to 'Enabled' and click 'Save' button to apply all changes
                  • Verify that the EVCS is activated in 'GX Settings/Integrations/Modbus Devices/Discovered Devices'
                  • Communication with the GX device via MQTT
                  • Verify that the GX device is running version v3.80 or later
                  • Verify that 'MQTT Access' is enabled in 'GX Settings/Integrations'
                  • Use the 'Discover' button to search for GX devices on your network, or enter the 'IP' and 'VRM ID' manually
                  • Activate pairing mode on the GX device in 'Settings/Integrations/MQTT Devices'
                  • Use the 'Pair' button to link the EVCS with the GX device via MQTT
                  • Set 'Communication' to 'Enabled' and click 'Save' button to apply all changes
                  • Applies only to internal auto-mode algorithms
                  • Applies only to internal auto-mode algorithms
                  • Applies only to internal auto-mode algorithms
                  • only if 'Allow battery/grid power for auto mode' activated
                  • Applies only to internal auto-mode algorithms
                  • Applies only to internal auto-mode algorithms
                  • The 'Input current limit' value is received from the inverter. You can modify this value in the inverter settings via the GX Remote Console or the VictronConnect app
                  • Enable only if your installation has no backup battery
                  • Applies only to internal auto-mode algorithms
                  NOTE: If you have enabled this feature, be sure that you added the correct IP address of the GX device to the 'GX IP address' above or to the 'whitelist table' below. Otherwise, the GX device will not communicate with EVCS!
                  №IP addressDelete
                  Light Ring
                  Disconnected
                  Connected
                  Waiting for start
                  Waiting for RFID
                  Waiting for solar energy
                  Low SoC
                  Charging manual
                  Charging auto
                  Charged
                  Error
                  Limit
                  Others
                  Scheduler
                  Scheduled mode requires local time synchronisation. Make sure the EVCS has an internet connection and the time zone is set correctly (General ->Date & Time).
                  №StatusTimeCurrent(A)SummaryRepeatEnableEditRemove
                  *Unsaved changes
                  WiFi
                  №SSIDPasswordUseDelete

                  Login

                  Sign In to your account

                  Error: 404

                  Page not found!

                  Error: 503

                  Service Unavailable!